Range Rover, Land Rover and Jaguar Cylinder Head and Head Gasket Repair
This page covers suspected or test-confirmed head and gasket faults and the work on those components. If you only have a temperature warning or an unidentified coolant leak, start with overheating diagnosis.
Persistent coolant loss, overheating, poor compression or contamination can point toward cylinder-head trouble, but the head gasket is not the only possible cause. We test the fault and check whether the head, block and cooling system remain serviceable before pricing a gasket repair or wider rebuild.
Request a head repair quote · Overheating repair
How Much Does a Head Gasket Repair Cost?
The cost changes with engine layout, access and damage. A gasket repair on a sound, tested head is different from replacing valves, machining a distorted head or repairing an overheated block. We do not quote one figure for the 204DTD, 306DT and AJ133 V8 as if their work were identical.
| Result | Work that may be quoted |
|---|---|
| External cooling leak | Repair the source and confirm system integrity |
| Gasket fault, head serviceable | Remove, test, prepare and refit the specified head components |
| Cracked or badly distorted head | Compare a replacement/repairable head and wider engine work |
| Block or bearing damage | Assess an engine rebuild or replacement route |
The named prices in Engine Rebuild Cost apply to own-engine rebuild starting scopes, not a fixed head-gasket service. We provide a repair amount once testing establishes the required work.
How We Test Coolant Loss and Compression
We review the vehicle's temperature history and signs of external leakage, then use appropriate cooling-system, combustion-gas and compression or leakage tests. No single symptom proves a head gasket has failed. An external leak should not lead to unnecessary head removal.
Gasket Failure versus a Cracked Cylinder Head
Removing a head exposes the gasket and mating surfaces. The head may need pressure testing and measurement for distortion or cracks before reuse. A new gasket against an unserviceable surface can fail again. We describe any machining or replacement required in the quote.
What If the Engine Has Overheated Severely?
Overheating can affect pistons, bores, bearings and the block as well as the head. Tell us how far it was driven after the warning, whether coolant entered the oil and whether the engine still turns. Those details help determine whether a targeted head repair remains appropriate. See seized-engine assessment if it will not turn.
Does the Quote Include Cooling Components?
Water pumps, hoses, radiator, thermostat, crossover pipes and other cooling ancillaries are identified separately where needed. Fixing internal damage without addressing the cause of overheating would leave the car vulnerable to a repeat event. Your written quote should show both the engine and cooling-system work.
Book a Cylinder-Head Assessment
Send your registration, engine badge, coolant and temperature symptoms, prior test results and current vehicle location. We will tell you what can be assessed without dismantling and when a paid strip-down decision is needed. Request an initial quote.
Cylinder-Head Work on Diesel and Petrol Engines
The diagnosis should follow the specific engine, not just the vehicle brand. A 306DT diesel with coolant loss, a 204DTD Ingenium diesel after timing failure and an AJ133 V8 with a cooling complaint can lead to different checks and parts lists. Engine identity, head condition and installation access all influence a full price. We identify the application before suggesting that a gasket kit is the solution.
Why the Cooling Fault Must Be Repaired Too
If a failed pump, leak or restriction caused the overheating, repairing the head alone leaves that cause in the vehicle. We test the system and itemise the associated cooling components. An engine rebuild price and a radiator or pump price are not interchangeable; both may appear in a full vehicle quote. We explain what testing after assembly will confirm that the repair is holding.
What If the Cylinder Head Cannot Be Reused?
We compare a suitable replacement head, available repair method and the economic case for wider engine work. A head may fail pressure or crack testing even if its surface can be machined. We obtain your approval for the changed parts list rather than refitting a component that has not passed the necessary checks. Any alternative unit must be matched to the actual engine and equipment.
Evoque and Discovery Sport Head Gasket Repair
We establish whether test results actually point to a head or gasket fault before dismantling. AJ200D is a family alias; we check the VIN. The head condition, mating surface and cause of coolant loss influence the repair price. We itemise testing, machining if suitable, seals and assembly, with cooling ancillaries separately identified rather than implying a new gasket alone resolves every complaint.
Engine details · Model details
Discovery 4 and Sport TDV6 Cylinder Heads
The V6 head repair scope depends on which components are affected and the condition after overheating or timing damage. We inspect the relevant head and engine evidence before deciding what can be reused. Block damage or contamination can make a wider rebuild more suitable. Your quote explains why any additional component is needed, rather than treating all V6 head work as the same service.
Engine details · Model details
AJ126 Supercharged V6 Head Repair
We distinguish a compression or cooling fault from boost and ancillary complaints before taking the head off. Once removed, testing and measurement determine whether it remains serviceable. The quote identifies component work and installation labour for the actual vehicle. Supercharger and cooling-system components are assessed as connected items, not automatically made new by a head repair.
Engine details · Model details
AJ133 V8 Head and Valve Work
Timing-related valve damage and overheating can lead to different head work. We check the reported event, establish the affected parts and test the head before reuse. Machining is proposed only where suitable for the component and specification. A cracked or unserviceable head requires an alternative and your approval of the changed scope before assembly continues.
Engine details · Model details
Frequently Asked Questions
Does coolant loss always mean a failed head gasket?
No. External leaks and other faults can produce the same symptom.
Can a cracked head be repaired?
Sometimes, depending on the location and available repair method. Testing is required before reuse is promised.
Should I keep driving if the temperature rises?
Stop safely and arrange assessment; continued overheating can increase engine damage.
Can you assess a vehicle already at another garage?
Send the diagnostic report, VIN and location. We can agree whether the whole vehicle or removed engine is the practical assessment route.
Will you obtain approval for additional work?
Yes. We explain findings outside the agreed scope and seek approval of the revised work before proceeding.
Will you repair the cause of overheating too?
We identify related cooling faults and quote the necessary components separately so the head repair does not leave an established cause unresolved.
Speak to Our Specialist Technicians
Our specialist technicians have 15+ years’ experience and 3,200+ engine rebuilds. Our rebuild work includes a 12-month unlimited-mileage warranty on covered components and labour, subject to the written warranty terms and the required chargeable 2,000-mile service. No deposit is required for standard engine work; any advance payment for bespoke parts is agreed separately.
Call 01268 944339, WhatsApp 07351 691324, email info@rangeroverengines.uk or request a free initial quote.
Workshop: Unit A5, Windsor Road Commercial Estate, Ramsden Heath, Billericay, Essex CM11 1QE. Hours: Monday–Friday 9am–6pm; Saturday 11am–2pm.
Related Repair and Booking Routes
Crankshaft failure repair · Diesel injector engine repair
See model-specific rebuild starting prices.
Contracting company: JLR Engine Specialists Ltd (company number 16500838). We operate one workshop at Billericay; other areas are served through arranged collection.